Tech Talk

Latest activity

• • lupecastro@lupecastro

  

  lupecastro added a new discussion topic 2006 tacoma trd package in the group Quick-Strut® - Monroe Shocks and Struts 21 days ago

  Will the 171371 be the same replacement as of the original blistein structs that came with truck.
• • Tenneco Tech Rep Trevor M@TrevorM

  

  Tenneco Tech Rep Trevor M replied on the discussion topic Class A RV Front End Height Low after 557003 Installation in the group Gas-Magnum® - Monroe Shocks and Struts 30 days ago

  Hello, Shocks cannot support the weight of the vehicle and thus they have no impact on ride height. The only way a shock alters ride height in this situation is if it was too short and was being fully extended and pulling the suspension down. 
• • Tenneco Tech Rep Trevor M@TrevorM

  

  Tenneco Tech Rep Trevor M replied on the discussion topic sensitrac 58241 specs in the group Load Adjusting Shock Absorbers - Monroe Shocks and Struts 30 days ago

  Hello, The upper mounting is a 5/8 inch inside diameter bushing with no steel sleeve inside of it.  The bushing measures 1 5/16 wide.  The lower mounting is a rubber bushing with a steel sleeve in it and the sleeve measures 1/2 inch...
• • Ron Brittain@RonB

  

  Ron Brittain added a new discussion topic Class A RV Front End Height Low after 557003 Installation in the group Gas-Magnum® - Monroe Shocks and Struts 33 days ago

  I just picked up a 97 National RV with Chevy Vortex engine with new 557003 installed and the front end is significantly lower that the back.  Could the wrong size shocks have been installed?
• • tteksystems@tteksystems

  

  tteksystems added a new discussion topic Flange Dimensions in the group Ultra® EPA Catalytic Converters - Walker 33 days ago

  I just bought a CAT back system in pieces with the following Walker part #s Walker 53389 CAT Converter non Carb Compliant Walker 54373 Resonator Assembly Walker 18910 SoundFX Muffler I do not understand why the flange on the 53389 is literally...
• • Steven A Tobey@BassLake1

  

  Steven A Tobey added a new discussion topic Flange dimensions in the group Hardware and Accessories - Walker 39 days ago

  On the flanges you show, particularly the 31965, there are no dimensions shown? The two dimensions I'm looking for are the diameter of the center hole and the bolt/stud hole centers. I'm trying to make an exhaust for a non-standard, i.e. no...
• • Steven A Tobey@BassLake1

  

  Steven A Tobey added a new discussion topic Flange dimensions in the group Hardware and Accessories - Walker 39 days ago

  On the flanges you show, particularly the 31965, there are no dimensions shown? The two dimensions I'm looking for are the diameter of the center hole and the bolt/stud hole centers. I'm trying to make an exhaust for a non-standard, i.e. no...
• • tom@butch

  

  tom added a new discussion topic sensitrac 58241 specs in the group Load Adjusting Shock Absorbers - Monroe Shocks and Struts 41 days ago

  Hi, I am attempting to get more details on this part 58241 shock. I would like to know what the upper and lower mounting bushing id is. Also what the overall width of bushing. I am atttempting to use this shock on a different vehicle than listing is...
• • Tenneco Tech Rep Trevor M@TrevorM

  

  Tenneco Tech Rep Trevor M replied on the discussion topic Conversion KIT 90012 - for 2002 Cadilac Escalade in the group Conversion Kits - Monroe Shocks and Struts 41 days ago

  Hello, If the onboard compressor is not functional, the rear air shocks would need to be inflated using an external compressor and add-on airlines from the airline kit AK29.
• • Christopher McKenna@CDMCKENNA65

  

  Christopher McKenna added a new discussion topic Conversion KIT 90012 - for 2002 Cadilac Escalade in the group Conversion Kits - Monroe Shocks and Struts 45 days ago

  In the directions it states that air should be added to the shock prior adding load to the shock.  Step 16.  IF your compressor is not working to add air through the vehicle, how do you add the air to the shock?  
• • Tenneco Tech Rep Trevor M@TrevorM

  

  Tenneco Tech Rep Trevor M replied on the discussion topic 139104 Quick Strut in the group Quick-Strut® - Monroe Shocks and Struts 46 days ago

  Hello, Yes, the ZW7 Smooth Ride package only affects the rear shocks.  The 139104 Quick Strut would be applicable for the front of this vehicle. 
• • kpbtech@kpbtech

  

  kpbtech added a new discussion topic 139104 Quick Strut in the group Quick-Strut® - Monroe Shocks and Struts 47 days ago

  Will the 139104 Quick Strut fit my 2008 Chevrolet Avalanche with the ZW7 Smooth Ride option ?
• • kpbtech@kpbtech

  

  kpbtech added a new discussion topic 139104 Quick Strut in the group Quick-Strut® - Monroe Shocks and Struts 47 days ago

  Will the 139104 Quick Strut fit my 2008 Chevrolet Avalanche with the ZW7 Smooth Ride option ?
• • Tenneco Tech Rep Trevor M@TrevorM

  

  Tenneco Tech Rep Trevor M replied on the discussion topic 901460 in the group Max-Lift® - Monroe Shocks and Struts 48 days ago

  Hello, The Monroe Lift Support 901460 falls into our Universal category.  This does not have a vehicle specific application. 
• • Donny Osbourn@Osbourn

  

  Donny Osbourn added a new discussion topic 901460 in the group Max-Lift® - Monroe Shocks and Struts 54 days ago

  Can I please get an application for the 901460 lift supports.  I cannot find any via my servicing warehouse nor any cataloging. Thanks 
• • Charles Brown@CharlesBrown

  

  Charles Brown added a new discussion topic Walker Quiet Flow SS Mufflers in the group Quiet-Flow® SS - Walker 58 days ago

  Does anyone know if Walker Quiet Flow SS mufflers are shipped from the manufacturer in a suitable shipping box with packaging to protect them from damage? They are great muffles and fit my car perfectly, but those I have ordered from Amazon and...
• • Matt@Viking00

  

  Matt replied on the discussion topic What is the difference between W0133-2038272 and 19160-05589567 in the group OESpectrum® - Monroe Shocks and Struts 59 days ago

  Wow, I feel really silly right about now. I realize now what I did. Thanks for getting back to me.  So a potentially smarter question would be, is there another Monroe option for just the strut other than the 72300 and 72299 for my vehicle? Or...
• • Tenneco Tech Rep Trevor M@TrevorM

  

  Tenneco Tech Rep Trevor M replied on the discussion topic What is the difference between W0133-2038272 and 19160-05589567 in the group OESpectrum® - Monroe Shocks and Struts 59 days ago

  Hello, The part numbers you have referenced are not Monroe parts numbers.  Unfortunately, since those are not our numbers we have no way of trying to help decipher the difference between them. 
• • Matt@Viking00

  

  Matt added a new discussion topic What is the difference between W0133-2038272 and 19160-05589567 in the group OESpectrum® - Monroe Shocks and Struts 61 days ago

  I have a 2007 hyundai santa Fe. These two matched as struts that would fit but I cant find anywhere that says the difference between the two. How do I choose? Thanks for your time. 19160-05589567 W0133-2038272
• • Matt@Viking00

  

  Matt joined the group OESpectrum® - Monroe Shocks and Struts 61 days ago

• « Previous
• 1
• 2
• 3
• 4
• 5
• 6
• 7
• Next »